Driving force coordinated control of an 8 ×8 in-wheel motor drive vehicle with tire-road friction coefficient identification

Because of the complexities of tire-road interaction,the wheels of a multi-wheel distributed electric drive vehicle can easily slip under certain working conditions.As wheel slip affects the dynamic per-formance and stability of the vehicle,it is crucial to control it and coordinate the driving force.With this aim,this paper presents a driving force coordination control strategy with road identification for eight-wheeled electric vehicles equipped with an in-wheel motor for each wheel.In the proposed control strategy,the road identification module estimates tire-road forces using an unscented Kalman filter al-gorithm and recognizes the road adhesion coefficient by employing the recursive least-square method.According to road identification,the optimal slip ratio under the current driving condition is obtained,and a controller based on sliding mode control with a conditional integrator uses this value for accel-eration slip regulation.The anti-slip controller obtains the adjusting torque,which is integrated with the driver-command-based feedforward control torque to implement driving force coordination control.The results of hardware-in-loop simulation show that this control strategy can accurately estimate tire-road forces as well as the friction coefficient,and thus,can effectively fulfill the purpose of driving force coordinated control under different driving conditions.     

Optimization of process parameters of the activated tungsten inert gas welding for aspect ratio of UNS S32205 duplex stainless steel welds

The activated TIG (ATIG) welding process mainly focuses on increasing the depth of penetration and the reduction in the width of weld bead has not been paid much attention. The shape of a weld in terms of its width-to-depth ratio known as aspect ratio has a marked influence on its solidification cracking tendency. The major influencing ATIG welding parameters, such as electrode gap, travel speed, current and voltage, that aid in controlling the aspect ratio of DSS joints, must be optimized to obtain desirable aspect ratio for DSS joints. Hence in this study, the above parameters of ATIG welding for aspect ratio of ASTM/UNS S32205 DSS welds are optimized by using Taguchi orthogonal array (OA) experimental design and other statistical tools such as Analysis of Variance (ANOVA) and Pooled ANOVA techniques. The optimum process parameters are found to be 1 mm electrode gap, 130 mm/min travel speed, 140 A current and 12 V voltage. The aspect ratio and the ferrite content for the DSS joints fabricated using the optimized ATIG parameters are found to be well within the acceptable range and there is no macroscopically evident solidification cracking.     

一种鱼雷自导信号频率检测方法研究

靶场在进行智能鱼雷鉴定试验任务时,实时准确地检测出鱼雷自导信号的频率成分是靶标信号处理中的重要环节,谱线比值法便是靶标进行信号处理时检测信号频率的一种有效方法。本文介绍了谱线比值法的基本原理,针对目前鱼雷自导信号特点,对该方法提出了改进方案并进行了仿真。仿真结果表明,经改进的谱线比值法能够满足靶标检测复杂鱼雷自导信号体制下信号频率的使用要求。     

数值模拟气/气喷嘴速度比对燃烧性能的影响

为研究应用于全流量补燃循环发动机的不同气/气喷嘴得到的燃烧流场,通过求解NavierStokes方程组,对不同燃料与氧化剂速度比下的流动燃烧过程进行了数值计算,计算结果与实验结果吻合。仿真结果表明:增加速度比能使燃烧火焰面提前,燃烧效率变大。如果发动机的长度受到限制,可以适当增加速度比以实现高效燃烧。     

基于改进LMS算法的复合材料超声检测缺陷识别

在径向基函数（RBF）神经网络实现无人机复合材料超声检测脱粘缺陷识别时,针对最小均方（LMS）算法在确定网络输出权值时存在稳态失调误差和收敛速度相矛盾的问题,提出一种改进的自适应的变步长LMS算法．该算法根据反馈误差自适应确定步长,通过引进动量项加快收敛速度．将改进LMS算法应用到RBF网络缺陷识别中,结果表明该方法在稳态失调误差较小的情况下,能快速确定RBF网络的权值．改进的RBF网络能够较好地识别超声检测脱粘缺陷．     

阶比谱分析与汽车起动电机故障的实时诊断

本文主要论述阶比谱分析方法及其在汽车起动电机故障实时诊断中的应用。首先阐述了阶比谱分析的原理以及阶比采样中混迭与泄漏的产生及其抑制方法,然后讨论了如何在起动电机运行过程短、升速快的情况下获取感兴趣的噪声信号,进而采用阶比谱分析方法从信号中提取故障特征信息,最后利用阀值判别法起动电机的故障进行实时诊断。     

Effects of total pressures and equivalence ratios on kerosene/air rotating detonation engines using a paralleling CE/SE method

In this paper, the kerosene/air rotating detonation engines(RDE) are numerically investigated, and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation, instabilities, and propulsive performance. A hybrid MPI + OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC) systems. A series of cases with the total pressure of 1 MPa, 1.5 MPa, 2 MPa, and the equivalence ratio of 0.9, 1, 1.4 are simulated. On one hand, the total pressure shows a significant impact on the instabilities of rotating detonation waves. The instability phenomenon is observed in cases with low total pressure (1 MPa) and weakened with the increase of the total pressure. The total pressure has a small impact on the detonation wave velocity and the specific impulse. On the other hand, the equivalence ratio shows a negligible influence on the instabilities, while it affects the ignition process and accounts for the detonation velocity deficit. It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition. Little difference was observed in the thrust with different equivalence ratios of 0.9, 1, and 1.4. The highest specific impulse was obtained in the lean fuel cases, which is around 2700 s. The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.     

Research on fuze microswitch based on corona discharge effect

Abnormal voltages such as electrostatic, constant current, and strong electromagnetic signals can erro-neously trigger operation of MEMS pyrotechnics and control systems in a fuze, which may result in casualties. This study designs a solid-state micro-scale switch by combining the corona gas discharge theory of asymmetric electric fields and Peek's Law. The MEMS switch can be transferred from "off" to"on" through the gas breakdown between the corona electrodes. In the model, one of the two electrodes is spherical and the other flat, so a non-uniform electric field is formed around the electrodes. The theoretical work is as follows. First, the relation among the radius of curvature of the spherical electrode, the discharge gap, and the air breakdown voltage is obtained; to meet the low voltage (30-60 V) required to drive the MEMS switch, the radius of curvature of the spherical electrode needs to be 10-50 μm and the discharge gap between the two electrodes needs to be 9-11 μm. Second, the optimal ratio ε is introduced to parameterize the model. Finally, the corona discharge structural parameters are determined by comparing the theoretical and electric field simulation results. The switch is then fabricated via MEMS processing. A hardware test platform is built and the performing chip tested. It is found that when the electrode gap is 9 μm, the electrostatic voltage is at least 37.3 V, with an error of 2.6% between the actual and theoretical air breakdown voltages. When the electrode gap is 11 μm, the electrostatic voltage is at least 42.3 V, with an error of 10.5% between the actual and theoretical air breakdown voltages. Both cases meet the design requirements.     

Maximizing the ratio of two convex functions over a convex set

The purpose of this article is to present an algorithm for globally maximizing the ratio of two convex functions f and g over a convex set X. To our knowledge, this is the first algorithm to be proposed for globally solving this problem. The algorithm uses a branch and bound search to guarantee that a global optimal solution is found. While it does not require the functions f and g to be differentiable, it does require that subgradients of g can be calculated efficiently. The main computational effort of the algorithm involves solving a sequence of subproblems that can be solved by convex programming methods. When X is polyhedral, these subproblems can be solved by linear programming procedures. Because of these properties, the algorithm offers a potentially attractive means for globally maximizing ratios of convex functions over convex sets. © 2006 Wiley Periodicals, Inc. Naval Research Logistics, 2006     

编队战斗机超视距空战效能评估

第三代战斗机主要空战模式是超视距空战,对编队战斗机超视距空战的全过程进行分析,建立了战斗机编队和导弹的运动模型,以领先发射概率和空战交换比作为评估指标,对编队战斗机超视距空战效能进行评估,最后给出了算例,重点分析了地面防空火力和编队战斗机数量、携带导弹总数等因素对空战交换比的影响.